







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Most paver driveways in Florence-Graham run $7,000 – $18,000, and a typical 20-by-40-foot driveway takes three to five working days from demolition to the last sweep of joint sand. What pushes a job toward that ceiling here is almost always the base, not the pavers. On these old narrow lots, the strip beside the house is often too tight for a skid steer, so the crew sizes the excavation to what can pass. Call (833) 842-7204 for a free on-site estimate.
How Paver Driveways Get Built in Florence-Graham, Start to Finish
Here’s the order of operations we follow. It’s the same sequence whether the job is a fifteen-foot strip behind a bungalow or a double-wide driveway beside a converted garage, and it never gets shortened to save a day.
1. Walkthrough and permit decision (day 1)
We measure slope, drainage direction, and setback to the property line before anything moves. Because Florence-Graham is unincorporated, if the job touches the apron or curb cut out at the street, the permit path runs through LA County Public Works, and a sealed site plan is part of that submission. Plumbing, electrical, and gas under the slab get located in this same visit.
2. Demolition and haul-off (day 1)
The old surface and enough sub-base to reach a compactable depth come out. On a 5,000 – 6,000 square foot lot, dumping is a real logistical problem, so we stage debris in the driveway itself and haul once at the end of demo day. You should expect a full day of noise and a temporary gap along the sidewalk or alley.
3. Sub-base, grade, and compaction (days 1 – 2)
We cut to depth, lay a woven separation fabric, then place and compact aggregate in two lifts. Each lift gets a plate compactor pass you can watch happen. This is where most paver driveways in the Florence-Graham Clay Belt fail inside five years, so we don’t skip it. This is also the stage that runs long if the soil is expansive and needs an overdig.
4. Setting layer and paving (days 2 – 3)
A one-inch bedding sand course goes down, then the field pavers, then the edge course and a spiked restraint. Once the pattern is set, a rubber mallet and a plate compactor tighten the field, and you pick the joint sand. Most jobs are fully walkable by the end of this step.
5. Joint sand and a clean sweep (day 3 – 5)
Polymeric joint sand goes in, gets wetted, and cures. We mark the pull-in edge and leave you with a written note on when to park on it. Total elapsed time is three to five working days, and the longest single delay is usually the county permit on a curb-cut change.
Key Takeaways
- Paver driveways in Florence-Graham typically run $7,000 – $18,000.
- Most jobs finish in three to five working days.
- The base is the biggest factor, especially on expansive soil.
- Street-facing curb changes trigger a county permit.
The Paver Options You’ll Be Choosing Between

The pavers themselves are the easy part. Here’s what actually gets decided, and the honest trade-off for each.
- Interlocking concrete pavers, 2 3/8-inch standard: The workhorse for a residential driveway. Mix and match the 4×8, 4×4, and 8×8 modules for a running bond or basketweave. Lower cost per square foot, and the manufacturer color range is huge. Trade-off: on a hot day, unsealed concrete pavers can read a little plain.
- Clad or 3-inch thick pavers: About a third of the way up the cost curve from standard. Rated for heavier loads, so they make sense on a longer, heavier service drive behind a converted garage. Trade-off: more material cost, and color selection is narrower.
- Tumbled or antiqued finishes: Rounded edges and color mottling that mimic old brick, right for a 1920s – 1950s stucco bungalow. Trade-off: joint sand has to be refreshed more often because the wide joints wear faster.
- Permeable pavers with open joints: Good on the small lots that drain toward the house or street. Trade-off: higher material and base cost, and they need the right subsurface and slope to actually infiltrate.
- Edge restraint and spiked edging: The hidden piece that keeps the field from spreading. This is not something to shave off an estimate.
Belgard is the paver line most of our Florence-Graham customers land on because the color and shape range covers both the basketweave look and the cleaner contemporary bond. If your project moves beyond the drive into a full paver approach or a rear yard hardscape, that’s a separate scope we’d cover under Driveway & Pavers.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
What Paver Driveways Cost in Florence-Graham, CA
The range for paver driveway installation in Florence-Graham is $7,000 – $18,000. Five things push a job from the low end to the high end.
- Size and slope. A tight 20-foot strip sits low. A double-wide drive with a grade change toward the street sits high.
- Existing surface and base condition. A tired asphalt drive over a sound base saves demo and haul days. Old concrete over clay can require overdig.
- Soil and drainage. Expansive clay in parts of this area is the most expensive variable. If water pools at the low corner, a French drain or a graded swale gets added.
- Paver grade and pattern. Standard 2 3/8-inch concrete pavers anchor the low-to-mid range. Clad, permeable, or hand-set tumbled blends move it up.
- Permit and curb scope. A simple in-property paver drive is straightforward. A curb cut or apron replacement that runs through LA County Public Works adds paperwork, inspection time, and a fee.
A written estimate breaks out the base depth, the compaction method, the paver make and model, edge restraint, joint sand, haul-away, and any permit allowance. What it should not include: movable-item relocation, plumbing or electrical relocations discovered mid-job, or a drainage feature that wasn’t scoped on the walkthrough. Those get called out as line items before work starts. That’s what upfront pricing, no surprises means on a paver job.
See the difference
Before
After
Before
After
Before
AfterWhat Florence-Graham Homes Do to This Job
Florence-Graham is unincorporated Los Angeles County, so building permits come through LA County Public Works, not the City of LA. Any contractor who only knows municipal processes will guess wrong on the form, and that gap can cost you a week. On top of that, these lots are narrow, with roughly 3-foot side setbacks, so a skid steer can’t always reach a rear or side drive. We hand-carry more material here than on most jobs in the region. The housing stock is 1920s – 1950s single-story stucco and wood-frame bungalows, and a lot of them have a detached garage that families are converting. That means a second vehicle access point and a heavier service drive, so paver driveways in Florence-Graham have to carry more weight than a simple front apron. Expansive clay soils cause slab cracking in some blocks, and that same clay is the reason a paver driveway with a properly compacted aggregate base is a real long-term fix. The other local truth: Santa Ana winds and dry summer heat don’t hurt pavers the way they hurt roofs and fences, but they do dry out unsealed joints, so refill your sand roughly every two to three years.
Serving Florence-Graham, CA – Our Local Coverage Area
We serve Florence-Graham and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Paver Driveways in Florence-Graham
Most paver driveways in Florence-Graham finish in three to five working days. A standard 20-by-40-foot drive usually lands on the three-to-four-day side; a larger drive that includes a curb cut or drainage work stretches toward five. Call (833) 842-7204 for a timeline on your specific lot.
Often yes, depending on scope. If the work stays inside your property and only replaces the surface, a permit may not be required. If it changes the curb cut, apron, or grading that touches the public right-of-way, it goes through LA County Public Works. We confirm the permit path on the initial walkthrough before any work starts. Call (833) 842-7204 and we’ll tell you which path applies to your property.
In most cases yes. A paver driveway is a surface and base job, so as long as plumbing, gas, and electrical lines stay where they are, we work right around them. If a line runs under the drive and needs relocation, we flag it as a separate line item before demo day. Call (833) 842-7204 with your address and we’ll check the layout.
Paver driveway installation in Florence-Graham runs $7,000 – $18,000. The low end reflects a smaller drive over a sound existing base with standard 2 3/8-inch concrete pavers, and the high end reflects a larger or sloped drive, base overdig, a curbside permit, and a premium paver grade. Call (833) 842-7204 for an exact quote on your property – estimates are free.
Every paver driveway we install is covered by the 730-Day Done Right Promise, our two-year workmanship guarantee: if the base or the sett fails in that window, we make it right. The pavers also carry the manufacturer’s own material warranty. Homeowners often pair this with a new entry door on the converted garage, and that’s covered under Door Installation in Florence-Graham.
Groundwork Construction Co. covers the full Florence-Graham service area, and a paver driveway is one piece of that wider scope. When it’s time to price the job, call (833) 842-7204 for a free on-site estimate. We measure, talk through pavers and base depth, and leave you a written, line-item quote. No voicemail, no waiting until Monday. Live person, 24/7. The 730-Day Done Right Promise backs every driveway we build. See the wider scope on our Driveway & Pavers in Florence-Graham page, and the full market on our Florence-Graham service-area page. If your project also touches cabinetry or countertops from the same driveway-side garage conversion, our team covers that under Cabinets & Countertops in Florence-Graham.
Written by the team at Groundwork Construction Co.












