







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterStanding Seam Metal Roof in Inglewood, CA
A standing seam metal roof in Inglewood typically runs $28,000 to $52,000 for a full 1,600 to 2,200 sq ft home, installed with concealed fasteners and a manufacturer-backed finish on Kynar 500 panels. It’s the roof type Inglewood homeowners choose when they’re tired of replacing asphalt shingles every 15 to 18 years and want something that holds up to the marine layer, the June gloom, and the occasional Santa Ana wind without a single maintenance visit in between. We install standing seam as part of our full Roofing division, and we do it with the same upfront pricing and the same 730-Day Done Right Promise we put behind every project.
Groundwork Construction Co. of Inglewood handles standing seam installs from tear-off to final flashing inspection. The panels we set down are roll-formed from 24-gauge steel with a factory-applied finish, and we’ve been installing on Inglewood roofs since 2014. Our technicians have up to 12 years of experience on metal roof systems, and every one of them is background-checked and arrives in uniform.
If you’re ready to talk numbers, call (833) 842-7204. A live person answers, 24 hours a day, 7 days a week. No voicemail, no waiting until Monday.
Why standing seam makes sense on Inglewood roofs
Inglewood sits about 4 miles from the Pacific, and that proximity matters more than most homeowners realize. The onshore flow brings salt-heavy moisture and morning fog that soaks roof decks, then dries fast by midday. That wet-dry cycle is brutal on asphalt shingles, especially on north-facing slopes that stay damp longest. Standing seam panels shed water in a single sheet and the metal itself doesn’t absorb the moisture, so the cycle doesn’t degrade the roof. We typically see asphalt roofs in neighborhoods like Morningside Park and North Inglewood hit their first leak around year 14. A standing seam system, properly installed, is a 40-to-50-year roof with a manufacturer finish warranty behind it.
Inglewood is also in a high-wind zone. The city building department, following California Building Code, requires specific wind-uplift ratings for roof coverings, and standing seam panels with concealed clips are engineered to those uplift pressures. That’s part of why the material is a fit here, not just a style choice.

When You Need a Standing Seam Metal Roof
Here’s what we actually see walking Inglewood roofs, and how we know it’s time to move toward metal rather than patch another year of shingles:
- Your asphalt roof is past 15 years and you’ve already had one repair. Once you’ve got a second leak in two seasons, you’re throwing money at a roof that’s already past its service life. Metal ends that cycle.
- You’re getting wind-driven rain infiltration at the chimney or skylight. Standing seam systems use fully engineered flashing details rather than surface-caulked seals, which is why we prefer them on Inglewood homes with multiple roof penetrations.
- You’re planning to stay in the home long-term. If you’re looking at a 30-year horizon, the math on a single metal roof beats two more asphalt replacements by a wide margin.
- You want to address heat gain. Standing seam panels with a reflective finish help reduce attic heat load, which matters more in Inglewood’s inland-facing blocks like the Crenshaw corridor than people expect.
- Your HOA or the home’s architecture points toward metal. A growing number of Inglewood area homes and ADU additions are being designed with metal roofing from the start, and standing seam delivers the clean, low-profile look.
- You’ve had storm damage and insurance is involved. When a wind event takes panels or shingles, replacing with a system rated for the uplift pressures in this zone is the durable move.
What all six of those scenarios share is a decision about the long horizon. Standing seam is not the cheapest roof you can buy. It’s the one you buy once. If a repair is genuinely the right call, we’ll tell you – no-hassle upfront pricing means the number you see is the number you pay, whether that number is a patch or a full replacement.
Our Standing Seam Metal Roof Process
Standing seam is not a product you can install loosely. The panels are engineered to work as a system, and the quality difference between a 40-year roof and a 12-year roof usually comes down to installation detail. Here’s how we run the project:
- On-site assessment and measurement. We measure every plane, pitch, ridge, valley and penetration. We check deck condition and identify what’s under the existing roof so the estimate is real rather than a guess. This is where the free project estimate and design consult happens – call (833) 842-7204 to schedule.
- Deck evaluation and tear-off. Standing seam requires a solid, properly fastened substrate. We inspect and replace any soft or damaged sheathing, then install the underlayment that meets both the panel manufacturer and California code requirements for this wind zone.
- Panel layout and fabrication. Panels are formed to the exact run lengths so the roof has minimal end laps. We lay out the panels to align seams with the home’s lines, which is where a standing seam roof earns its clean look or doesn’t.
- Installation with concealed clips. Every panel locks down with clips engineered for wind uplift, and seams are mechanically crimped. There are no exposed fasteners on the field of the roof – that’s the whole point of the “standing seam” name.
- Flashing, ridge, valleys and penetrations. Chimneys, vents, skylights and valley transitions get fabricated metal flashing, not caulk. We walk the job for detail fit before we close it out.
- Final inspection with the homeowner. We do a full walkthrough, clean up, and hand over the paperwork covering the 730-Day Done Right Promise along with the manufacturer finish warranty.
One safety note: standing seam installs happen on a steep, hard metal surface. We don’t recommend homeowners walk a metal roof for inspections or DIY maintenance – a slip on a wet panel is far more serious than on shingles. Let our trained crews handle anything above the gutter line.

Standing Seam Metal Roof Pricing in Inglewood
Standing seam pricing in Inglewood lands higher than most of the country because of local labor rates, permit costs and the wind-uplift-ready substrate work required by code. Here are the ranges we see on actual Inglewood jobs:
| Line item | Typical range |
|---|---|
| Full standing seam install, 1,600 to 2,200 sq ft | $28,000 – $52,000 |
| Panel material (24-gauge steel, Kynar finish) | $9 – $16 per sq ft |
| Tear-off and deck repair | $1,800 – $4,500 |
| Underlayment and ice-water barrier | $700 – $1,600 |
| Flashing, ridge and penetration detail | $1,200 – $2,800 |
| Inspection and permit fees (Inglewood) | $400 – $900 |
What moves the number: roof complexity (valleys, dormers and skylights add flashing labor), pitch (steeper roofs slow the install), the gauge and finish you choose, and whether the existing deck needs partial replacement. A simple gable roof on a 1,800 sq ft Inglewood home typically comes in around $34,000 to $40,000. A complex hip-and-valley configuration with two skylights and a chimney can push toward $52,000.
We publish the number before work starts and stick to it. That’s what upfront pricing, no surprises means on a metal roof where honest builders sometimes hide costs. We also offer 0% financing for 18 months and $1,000 off projects over $10,000 – which on a standing seam job is real money. Every install is backed in writing by the 730-Day Done Right Promise, one of the longest workmanship guarantees in the residential construction space. If a panel, a clip or a seam fails within that window because of our work, we make it right.
Metal roofs are also a long-term cost play. When we quote a standing seam install against two more asphalt cycles over 40 years – including inflation on labor and disposal – standing seam wins on total cost in most Inglewood scenarios. Call (833) 842-7204 for a free estimate specific to your roof.
FAQs – Standing Seam Metal Roof
How much does a standing seam metal roof cost in Inglewood?
A standing seam metal roof in Inglewood typically costs $28,000 to $52,000 for a 1,600 to 2,200 sq ft home, depending on roof complexity, pitch and finish. Panel material alone runs $9 to $16 per square foot, and tear-off, flashing and permitting add another $4,000 to $9,000. Call (833) 842-7204 for an exact quote on your roof – estimates are free.
How long does a standing seam metal roof last?
A properly installed standing seam metal roof lasts 40 to 50 years on 24-gauge steel with a factory finish, and often longer on heavier-gauge panels. The failure point on metal roofs is almost never the panel; it’s the installation detail at flashing, closures and seams. That’s why we back the workmanship with our 730-Day Done Right Promise in addition to the manufacturer warranty.
Can you install a standing seam metal roof over an existing roof?
We don’t recommend installing standing seam over an existing roof in most Inglewood cases. Standing seam needs a solid, properly fastened deck to hold clips at the uplift pressures this wind zone requires. We inspect the deck, and if it’s sound we can discuss options; otherwise we tear off first. Call (833) 842-7204 and we’ll take a look and tell you straight.
Is a metal roof louder than asphalt shingles in the rain?
A standing seam metal roof installed with solid sheathing and proper underlayment is not noticeably louder than asphalt shingles from inside the home. The old “talking drum” reputation comes from metal roofs installed over exposed purlins with no solid deck. Our installs use continuous decking and underlayment, which is standard practice in Inglewood and required for the wind rating anyway.
If you’re ready for a roof you won’t touch again for decades, call (833) 842-7204 for a free project estimate and design consult. A live person answers 24 hours a day, and we’ll walk your roof, measure every plane, and put a real number in front of you before any work starts. If you’d like to see the full range of roofing work we handle in Inglewood, start with our Inglewood service area page.
Written by the team at Groundwork Construction Co. of Inglewood, serving Inglewood.


